Cisco wifi AIR-SAP2602I-E-K9 Aironet wireless 2600 Access Point Dual-band autonomous 802.11a/g/n internal antennas.

-  2.4 GHz, Gain 4 dBi, internal omnidirectional, horizontal beamwidth 360°

-  5 GHz, Gain 4 dBi, internal omnidirectional, horizontal beamwidth 360°

-  10/100/1000BASE-T autosensing (RJ-45)

-  Management console port (RJ-45)

-  Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors

-  Nonoperating (storage) temperature: -22 to 158°F (-30 to 70°C)

-  Nonoperating (storage) Altitude Test: 25˚C, 15,000 ft.

-  Operating temperature: -4 to 131°F (-20 to 55°C)

-  Operating humidity: 10 to 90 % (noncondensing)

-  Operating Altitude Test: 40˚C, 9843 ft.

-  256 MB DRAM

-  32 MB flash

-  802.3af Ethernet Switch

-  Cisco AP2600 Power Injectors (AIR-PWRINJ4=)

-  Cisco AP2600 Local Power Supply (AIR-PWR-B=)

-  AP2600: 12.95W

Note: When deployed using Power over Ethernet (PoE), the power drawn from the power sourcing equipment will be higher by some amount depending on the length of the interconnecting cable. This additional power may be as high as 2.45W, bringing the total system power draw (access point + cabling) to 15.4W.

-  Torx security screw, included with the access point

-  Mounting bracket: AIR-AP-BRACKET-8= (available as spare)

-  Physical security kit: AIR-SEC-50= (sold separately), with 50 pcs. security screws used to secure the access point onto wall-mounting bracket, 50 pcs. RJ-45 caps and 2 pcs. unlock keys used to block physical access to Ethernet ports

-  Safety: UL 60950-1, CAN/CSA-C22.2 No. 60950-1, UL 2043, IEC 60950-1, EN 60950-1

-  Radio approvals: FCC Part 15.247, 15.407, RSS-247 (Canada), EN 300.328, EN 301.893 (Europe), ARIB-STD 66 (Japan), ARIB-STD T71 (Japan), EMI and susceptibility (Class B), FCC Part 15.107 and 15.109, ICES-003 (Canada), VCCI (Japan), EN 301.489-1 and -17 (Europe), EN 50385

-  IEEE standards: IEEE 802.11a/b/g, 802.11n, 802.11h, 802.11d, IEEE 802.11ac

-  Security: 802.11i, WPA2, WPA, 802.1X, AES

-  Extensible Authentication Protocol (EAP) types: EAP-Transport Layer Security (TLS), EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAPv2), Protected EAP (PEAP) v0 or EAP-MSCHAPv2, EAP-Flexible Authentication via Secure Tunneling (FAST), PEAP v1 or EAP-Generic Token Card (GTC), EAP-Subscriber Identity Module (SIM)

-  Multimedia: Wi-Fi Multimedia (WMM)

-  Other: FCC Bulletin OET-65C, RSS-102

Cisco Unified Wireless Network Software Release 7.2.110 or later.

-  Cisco 2500 Series, Cisco Wireless LAN Controller Module (WLCM) on Cisco Services Ready Engine (SRE) for Integrated Services Router Generation 2 (ISR G2), Cisco Wireless Services Module 2 (WiSM2), Cisco 5500 Series, Cisco Flex 7500 Series

-  3x4 multiple-input multiple-output (MIMO) with three spatial streams

-  Maximal ratio combining (MRC)

-  802.11n and 802.11a/g beamforming

-  20- and 40-MHz channels

-  PHY data rates up to 450 Mbps (40-MHz with 5 GHz)

-  Packet aggregation: Aggregated MAC Protocol Data Unit (A-MPDU) (Tx/Rx), Aggregated MAC Protocol Service Unit (A-MSDU) (Tx/Rx)

-  802.11 dynamic frequency selection (DFS)

-  Cyclic shift diversity (CSD) support