| TECHNICAL SPECIFICATIONS |
| AP type |
Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n 4x4 MIMO |
| Radio |
Four spatial stream SU-MIMO for up to 1,733 Mbps wireless data rate to a single client device.
Three spatial stream MU-MIMO for up to 1,300 Mbps wireless data rate to up to three MU-MIMO capable client devices simultaneously. |
| Maximum number of associated client devices |
Up to 256 associated client devices per radio |
| Maximum number of BSSIDs |
16 BSSIDs per radio |
| Supported frequency bands (country-specific restrictions apply) |
- 2.400 to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz |
| Dynamic frequency selection (DFS) optimizes the use of available RF spectrum |
| Supported radio technologies |
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) |
| Supported modulation types |
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM |
| 802.11n high-throughput (HT) support |
HT20/40 |
| 802.11ac very high throughput (VHT) support: |
VHT20/40/80/160 |
| Supported data rates (Mbps): |
-802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 600 (MCS0 to MCS31)
- 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4) |
| 802.11n/ac packet aggregation: |
A-MPDU, A-MSDU |
| Transmit power |
Configurable in increments of 0.5 dBm |
| Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): |
- 2.4 GHz band: +24 dBm, 18 dBm per chain
- 5 GHz band: +24 dBm, 18 dBm per chain |
| WI-FI ANTENNAS |
| Antenna |
Four RP-SMA connectors for external dual band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 2.5 dB in 2.4 GHz and 1.5 dB in 5 GHz. |
| OTHER INTERFACES |
| Interfaces |
• Two 10/100/1000BASE-T Ethernet network interfaces (RJ-45)
- Auto-sensing link speed and MDI/MDX
- Link Aggregation support to achieve platform throughput up to 2 Gbps
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3af or 802.3at PoE
• DC power interface, accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length
• USB 2.0 host interface (Type A connector)
• Bluetooth Low Energy (BLE) radio
- Up to 4dBm transmit power (class 2) and
-94dBm receive sensitivity
- Integrated antenna, -5dBi gain (30 degrees downtilt)
- Can be disabled with configuration
• Visual indicators (tri-color LEDs): For system and radio status
• Reset button: Factory reset (during device power up)
• Serial console interface (RJ-45)
• Kensington security slot |
| FLEXIBLE OPERATION AND MANAGEMENT |
| Controller-managed mode |
When managed by Aruba Mobility Controllers, Aruba 320 Series Access Points offer centralized configuration, data encryption, policy enforcement, and network services, as well as distributed and centralized traffic forwarding. |
| Aruba Instant mode |
In Aruba Instant mode, a single AP automatically distributes the network configuration to other Instant APs in the WLAN. Simply power-up one Instant AP, configure it over the air, and plug in the other APs – the entire process takes about five minutes. If WLAN requirements change, a built-in migration path allows 320 series Instant APs to become part of a WLAN that is managed by a Mobility Controller |
| Remote AP (RAP) |
for branch deployments |
| Air monitor (AM) |
for wireless IDS, rogue detection, and containment. |
| POWER SOURCES AND POWER CONSUMPTION |
| Power Sources |
• Maximum (worst-case) power consumption: 20W (802.3at PoE), 13.5W (802.3af PoE) or 18.5W (DC)
- Excludes power consumed by external USB device (and internal overhead); this could add up to 6W (POE) or 5.5W (DC) for 5W/1A USB device.
• Maximum (worst-case) power consumption in idle mode: 8W (PoE) or 7W (DC)
• Direct DC source: 12 Vdc nominal, +/- 5%
• Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af/802.3at compliant source
- Unrestricted functionality with 802.3at PoE
- Power-save mode with reduced functionality from 802.3af PoE
> USB port disabled
> Second Ethernet port disabled
> 2.4 GHz radio in 1x1:1 mode
• Power sources sold separately
• When both power sources are available, DC power takes priority
|
| MECHANICAL SPECIFICATIONS |
| Dimensions/weight (unit, excluding mount accessories): |
- 203mm (W) x 203mm (D) x 57mm (H) 8.0” (W) x 8.0” (D) x 2.2” (H)
- 950g/34 oz |
| Dimensions/weight (shipping): |
- 315mm(W) x 265mm(D) x 100mm (H) 12.4” (W) x 10.4” (D) x 3.9” (H)
- 1,350g/48 oz |
| ENVIRONMENTAL SPECIFICATIONS |
| Operating conditions |
• Operating:
- Temperature: 0° C to +50° C (+32° F to +122° F)
- Humidity: 5% to 93% non-condensing |
| Storage and transportation conditions |
- Temperature: -40° C to +70° C (-40° F to +158° F) |
| RELIABILITY |
| Mean Time Between Failure (MTBF): |
MTBF: 739,935 hrs (84.5yrs) at +25C operating temperature (AP-325) |
| MINIMUM OPERATING SYSTEM SOFTWARE VERSIONS |
| ArubaOS |
6.4.4.0 |
| Minimum Software Release |
4.2.2.0 |
Switch
.png){kind=icon}
.png){kind=logo}
.jpg)
.png){kind=logo}
Bạn đang cần tư vấn về sản phẩm: JW319A ?
Giá của bộ phát wifi Aruba Instant IAP-324 (RW) 802.11n/ac Dual 4x4:4 MU-MIMO Radio Antenna Connectors AP JW319A đã được gửi vào mail của bạn, bạn vui lòng check mail nhé.
Bộ phát wifi Aruba IAP-324 JW319A chịu tải tối đa được 256 người dùng trên 1 radio anh nhé.
Chào anh/chị, bộ phát wifi Aruba Instant IAP-324 hỗ trợ tối đa 32 SSID.