|
Ports
|
4 x 40 Gigabit Ethernet/16 x 10 Gigabit Ethernet
|
|
Optics
|
CFP-40G-LR4, 40G-CFP-SR4
FourX converter for 10 Gigabit Ethernet SFP+
|
|
Switch fabric connection
|
80 Gbps full duplex
|
|
Oversubscription
|
2:1 in Oversubscription mode 1:1 in Performance mode
|
|
Forwarding engine
|
- Equipped with DFC4-EXL for distributed forwarding, supporting 1 million forwarding entries, increased ACL entries to 256K, increased NetFlow entries to 1 million, and increased IPv4 forwarding speed to 60 mpps
- In addition to the increased NetFlow entries, supports in hardware Flexible NetFlow, Sampled NetFlow, and Egress NetFlow
- Increased performance of up to 60 mpps for Layer 2, IPv4 and Multiprotocol Label Switching (MPLS) forwarding, and up to 30 mpps for Generic Routing Encapsulation (GRE), IPv6, and VPLS forwarding
- Increased multicast routes to 256K (128K IPv4 + 128K IPv6)
- Support for 16K bridge domains, allowing the standard 4K VLANs to be reused across these bridge domains, effectively increasing the number of VLANs available in the system
- Increased MAC address table to 128K
- IPv4 Internet Group Management Protocol Version 3 (IGMPv3) snooping in hardware
- IPv6 Multicast Listener Discovery Version 2 (MLDv2) snooping in hardware
- Protocol Independent Multicast (PIM) registers in hardware
- IPV4 and IPv6 in IPv6 tunneling
- IPv6 in IPv4 tunneling (Intra-Site Automatic Tunnel Addressing Protocol [ISATAP], 6to4, GRE)
- Quality-of-service (QoS) support for uniform, short pipe, and pipe mode tunnel
- Terminate the tunnel in the same loopback
|
|
Security
|
- Layer 2 and Layer 3 Cisco TrustSec (Security Group Tagging & Security Group Access Control List) and IEEE 802.1ae (MACsec) Layer 2 encryption in hardware
|
|
Queues
|
- Receive: 1p7q4t/2p6q4t
- Transmit: 1p7q4t/2p6q4t
|
|
Queuing mechanisms
|
- Class-of-service (CoS)-based queue mapping
- Differentiated Service Code Point (DSCP)-based queue mapping
|
|
Scheduler
|
- Deficit Weighted Round Robin (DWRR)
- Weighted Random Early Detection (WRED)
|
|
Port buffers
|
- Port Group 1& 2 has combined Ingress packet buffer of 10 MB same as the Port Group 3 & 4
- Port Group 1 & 2 has combined Egress packet buffer of 176 MB same as Port Group 3 & 4
- Distribution of packet buffers among the ports in Performance or Oversubscribed mode is explained in more detail below
- Ingress buffer for Port Group (1&2) or Port Group (3&4):
◦ In Performance mode 1ms of storage = 10 MB or 10 MB/4 for each of the 4 x 10 Gigabit Ethernet
◦ In Oversubscribed mode = 10MB/2 for each of the 2 x 40GE ports and/or (10MB/4)/2) for each of the 8 x 10GE
- Egress buffer for Port Group (1&2) or Port Group (3&4):
◦ In Performance mode, 10 ms of storage equals 176 MB or 176 MB/4 for each of the 4 x 10 Gigabit Ethernet
◦ In Oversubscribed mode equals 176 MB/2 for each of 2 x 40 Gigabit Ethernet ports and/or (176/4)/2) for each of 8 x 10 Gigabit Ethernet
|
|
Hardware-based multicast replication
|
- Ingress and Egress mode
- Approximately 20 Gbps per replication engine
- Four replication engines per module delivering total throughput of 80 Gbps
|
|
Jumbo frame support for bridged and routed packets
|
Up to 9216 bytes
|
|
+ LED
|
New Blue Beacon LED added on front panel for slot-level and port-level service flashing indicator
|
|
EtherChannel Capacity
|
40 Gigabit Ethernet mode
- A maximum of 4 x 40 Gigabit Ethernet links, whether on one module or spread across multiple modules, is allowed in a single EtherChannel.
- This does not affect other modules in the system.
- 10 Gigabit Ethernet mode
- Up to eight 10 Gigabit Ethernet ports can be used in an EtherChannel, whether on one module or spread across multiple modules.
Best Practices
- EtherChannel should be two or four ports (or eight, with 10 Gigabit Ethernet ports)
|
|
Maximum port density per chassis
|
32 x 40 Gigabit Ethernet ports or 128 (+2 Supervisor Uplink) 10 Gigabit Ethernet ports (6509-E chassis)
44 x 40 Gigabit Ethernet ports or 176 (+2 Supervisor Uplink) 10 Gigabit Ethernet ports (6513-E chassis)
|
|
Maximum port density per VSS
|
64 x 40 Gigabit Ethernet ports or 256 10 Gigabit Ethernet ports (6509-E chassis)
88 x 40 Gigabit Ethernet ports or 352 10 Gigabit Ethernet ports (6513-E chassis)
|
|
Can be used to form virtual switch link
|
Yes (on all ports). Maximum of 4 x 40 G ports (refer to EtherChannel capacity section above)
|
|
Supervisor engines supported
|
Cisco IOS Supervisor Engine 2T and 2TXL
|
|
Can you upgrade WS-X6904-40G-2TXL to XL version with DFC4XL?
|
Yes. WS-6904-40G-2T can be upgraded to a XL version by swapping out the DFC4 with DFC4XL
|
|
Chassis supported
|
- Any Cisco Catalyst 6500 E-Series chassis, including 6503-E, 6504-E, 6506-E, 6509-E, 6509-V-E, 6513-E (NEBS compliant: operating temperature up to 55°C)
- Not supported in non-E Series chassis
|
|
Slot requirements
|
- Can occupy any slot in any Cisco Catalyst 6503-E, 6504-E, 6506-E, 6509-E, or 6509-V-E chassis
- Can occupy slots 1-6 and 9-13 in a Cisco Catalyst 6513-E chassis
|
|
Onboard memory
|
2 GB default (no higher upgrade)
|
|
Standard protocols
|
IEEE 802.1d, IEEE 802.1p, IEEE 802.1q, IEEE 802.1s, IEEE 802.1w, IEEE 802.3x, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3aq, and IEEE 802.3an
|
|
Physical specifications
|
- Occupies one slot in the Cisco Catalyst 6500 E-Series chassis
- Dimensions (H x W x D): 1.73 x 14.4 x 16 in. (4.4 x 35.6 x 40.6 cm)
- Weight: 12 lb excluding CFP components; .25 lb for each CFP component
|
|
Environmental conditions
|
Operating temperature:
- Agency-certified for operation: 32 to 104°F (0 to 40°C)
- Storage temperature: -40 to 167°F (-40 to 75°C)
- Relative humidity: 10 to 90 percent, non condensing
|
Switch
.png){kind=icon}
.png){kind=logo}
Bạn đang cần tư vấn về sản phẩm: WS-X6904-40G-2TXL ?